1. Home
  2. Instruments and Autopilots
  3. Sail and engine autopilots
  4. Autopilots Accessories
Back
-13%

Raymarine Volvo EVC Y-Motor Cable

(0)
Purchase 1 cable for each motor
Faq
Any questions about this product?
You'll find the answers you're looking for HERE
€ 101,00 € 115,90 -13%
Raymarine Command-Link cable 1 m NMEA 2000 F

Using the ECI-100 , you can connect selected Volvo Penta* engine EVC (Electronic Vessel Control) systems.
This allows you to view the following engine data on a connected Raymarine multifunction display and access full autopilot steering control on an IPS or Aquamatic system. Check compatible engines

Engine speed (rpm)
Engine hours
Engine oil temperature**
Engine coolant temperature**
Engine oil pressure**
Engine coolant pressure**
Engine fuel delivery pressure**
Engine fuel rate
Engine boost pressure**
Battery voltage
Transmission oil pressure**
Gearbox oil temperature**
Fuel level**
Boat speed**
Power Trim**
Rudder angle (only if connected to an IPS system)
Engine alarms
Overtemperature
Low oil pressure
Low oil level
Low system voltage
Low coolant level
Water in fuel
**Only available if Volvo sensor is installed*

Connecting your ECI-100 to your Volvo Penta EVC System couldn't be easier. Raymarine offers two wiring solutions, depending on the engine's age and installation type:
Latest Volvo Penta Engine EVC Systems - with an available multi-link hub
For new and recent Volvo Penta engine EVC systems, a multi-link hub should be available. This will have 6 connections, one of which must be available to connect your ECI-100.
This connection requires the Raymarine cable connection for use with the Volvo Penta engine. This cable is connected between the ECI-100's DeviceNet connector and the available socket on the multi-link hub.
For older EVC systems with Volvo Penta engines where a multi-link hub is not available, you must use the Raymarine E70240 Volvo Penta cable connection along with a Y-cable (E70241). This connects to the system as shown in the diagram.
Connecting the cables according to the diagram below will allow the ECI-100 to interface between the Volvo Penta engine EVC data bus and the Raymarine navigation STNG bus .
If a Volvo Penta IPS engine or Aquamatic steering system is installed, connecting a Raymarine EV-2 as shown in the diagram below will allow full control of the autopilot steering.
For engine data only, the connection between the ECI-100 and the Volvo Penta engine EVC system is identical (as shown in the diagram) but the Raymarine EV-2 is not required to be fitted.
EV-2 is connected to the Raymarine backbone via a SeaTalkng spur cable (SeaTalkng white EV-2 plug to use).

1) SeaTalk spur cable between the SeaTalk backbone and the EV2 SeaTalk connector
2) ECI-100 units
3) ST ng mains power supply (12 V dc)
4) Raymarine Volvo Penta Y-Frame Engine (E70241)
5) EV-2 - Evolution Autopilot
6) Raymarine connection cable (E70240) for use with Volvo Penta engines
7) System bus for use with Volvo Penta engines
D Buon giorno, questo cavo può essere utilizzato anche per collegare la strumentazione B&G ? Ho un volvo penta D2-50 del 2018 e la mia barca ha i plotter Zeus 3 Grazie
R 15-04-25 Buonasera, sì certo, però deve sempre acquistare un'interfaccia Volvo che converta i dati in NMEA 2000. Cordiali saluti. Luigi Bianchi
D ho fue motori volvo penta D3 da 160 cv. prima serie e vorrei sapere quale strumento raymarine serve per visualizzare i dati e correggere le impostazioni. grazie
R 19-06-24 Buongiorno, purtroppo con Volvo è sempre un problema, consiglio di consultare Volvo ed acquistare la loro Gateway di conversione dati in NMEA 2000. Cordiali saluti. Luigi Bianchi
D Salve io ho 2 motori volvo penta d3 da 160 del 2004 vorrei collegarli alla rete mnea 2000 che ho a bordo . Vorrei capire quali cavi comprare .
R 24-01-24 Buongiorno, consiglio di contattare Volvo perchè necessaria la loro Gateway di conversione dati da Volvo a NMEA 2000. Cordiali saluti. Luigi Bianchi
D buonasera ho un motore volvo penta d2 75cv del 2008 ed un plotter axiom . si puo' connettere per avere i dati motore su plotter? il seriale motore volvo e' 5103993918P. grazie
R 02-05-23 Buongiorno, purtroppo dovrà chiedere a Volvo l'interfaccia di conversione dati in NMEA 2000, non è sufficiente questo cavo. Cordiali saluti. Luigi Bianchi
D Salve con i kad 300 possibile ?
R 21-08-22 Buonasera, questo articolo è un semplice accessorio per eventuale collegamento di un autopilota Raymarine con alcuni motori Volvo. Nel Suo caso se intendo giusto, se vuole interfacciare un Chartplotter in NMEA 2000 con Volvo per visualizzare i motori, dovrà acquistare da Volvo la Gateway di conversione dati in NMEA 2000. Cordiali saluti. Luigi Bianchi
D Buongiorno e' compatibile con motore volvo penta 5.0 gxi del 2005? Grazie saluti Matteo
R 24-06-22 Buongiorno, non saprei, secondo me no perchè è per motori EVC. Eventualmente dovrebbe chiedere a Volvo, ma più che altro a Lei per cosa Le serve? Cordiali saluti. Luigi Bianchi
Autopilots Accessories
Products that may be of interest to you
Raymarine ECI-100 Engine Interface Painestore
- 13%
Raymarine ECI-100 Engine Interface
€ 398,00 € 457,50
Our strength: complete and reliable solutions.
Design
Design

Clear diagrams for easy installation.

Consulting
Consulting

Equipment suited to your needs.

Realization
Realization

High quality systems.

Do you need help?
Do you need help?

Guaranteed after-sales support.

Don't lose your way!
Subscribe to our free newsletter.
  • Contrassegno
  • Visa
  • Mastercard
  • Paypal
  • Bonifico
  • Scalapay
REGISTER
REGISTER